Piping
Calculate pipe weight, capacity, velocity, cross-sectional areas, slope and the weight of plates and sections for supports.
Pipe Weight Calculator
Calculate theoretical pipe mass from actual outside diameter, wall thickness, length and material density.
Open calculatorPipe Internal Volume Calculator
Find the full internal capacity of a straight pipe using its outside diameter, wall thickness and length.
Open calculatorPipe Flow Velocity Calculator
Calculate average full-bore velocity from inside diameter and volumetric flow, with results in m/s and ft/s.
Open calculatorPipe Pressure Drop Calculator
Calculate Darcy–Weisbach friction pressure drop, minor losses and elevation change from bore, length, flow and fluid properties, with Reynolds number and friction factor.
Open calculatorPipe Cross Section Area Calculator
Distinguish the internal flow area from the cross-sectional area of the pipe wall.
Open calculatorPipe Surface Area and Paint Calculator
Get a pipe's external surface area from its outside diameter and length, plus internal area, insulation cladding area and the paint needed from film thickness and volume solids.
Open calculatorPipe Slope Calculator
Calculate signed elevation change, slope percentage, gradient, ratio and angle along a horizontal run.
Open calculatorPipe Schedule Chart (NPS)
Pipe Schedule Chart
Look up outside diameter, wall thickness, bore and weight per meter of steel pipe by NPS and schedule (Sch 5S–160, STD, XS, XXS), and compare schedules.
Open calculatorASME B16.5 Flange Chart
Look up outside diameter, thickness, raised face, bolt circle, bolt count and size and bolt holes of ASME B16.5 Class 150 and 300 flanges (NPS 1/2–24) in mm and inches.
Open calculatorJIS B 2220 Flange Chart
Look up outside diameter, thickness, bolt circle (PCD), bolt count and thread size and bolt hole diameter of JIS B 2220 5K, 10K, 16K and 20K steel pipe flanges by nominal size (A).
Open calculatorMetric Bolt and Thread Chart
Look up pitch, tensile stress area, tap drill and spanner size of M3–M64 metric threads, and calculate proof load and an estimated tightening torque by property class.
Open calculatorH-Beam Size Chart
Look up dimensions, area, unit mass (kg/m), moments of inertia and section moduli of KS D 3502 and JIS G 3192 H-beams, and total weight from length and quantity.
Open calculatorSteel Weight Calculator
Calculate cross-sectional area, weight per meter and total weight of steel plate, flat, round, square and hexagonal bar, H-beams and angles from their dimensions.
Open calculatorWhat this section covers
Calculations that recur in piping design and material take-off: looking up the outside diameter, wall and bore of standard pipe, then pipe weight, internal volume, average velocity, cross-sectional areas, slope and the weight of steel for supports.
Piping calculations start from actual dimensions. Designations such as NPS or DN are not dimensions, so look up the outside diameter and wall in the pipe schedule chart first; feeding those into the weight, volume and velocity calculators keeps every step consistent.
Which tool should I use?
- Pipe Weight Calculator — Get pipe weight from OD, wall, length and material, including non-standard sizes
- Pipe Internal Volume Calculator — Get internal volume for hydrotest water, filling or draining
- Pipe Flow Velocity Calculator — Check average velocity from bore and flow, and compare candidate sizes
- Pipe Pressure Drop Calculator — Get friction and minor pressure losses and head loss from flow and fluid properties
- Pipe Cross Section Area Calculator — See flow area and metal area separately
- Pipe Surface Area and Paint Calculator — Get external and internal surface area, cladding area and paint volume for painting and insulation take-off
- Pipe Slope Calculator — Reconcile drain or condensate falls in %, mm/m and 1:X
- Pipe Schedule Chart (NPS) — Find the actual OD, wall, bore and kg/m from NPS and schedule
- ASME B16.5 Flange Chart — Look up outside diameter, bolt circle and bolt count and size of ASME B16.5 Class 150 and 300 flanges
- JIS B 2220 Flange Chart — Look up outside diameter, bolt circle and bolt count and size of JIS B 2220 5K, 10K, 16K and 20K flanges
- Metric Bolt and Thread Chart — Look up bolt and thread pitch, tap drill, spanner size, proof load and an estimated tightening torque
- H-Beam Size Chart — Look up unit mass, area, moments of inertia and section moduli of KS and JIS H-beams
- Steel Weight Calculator — Weigh plate, round bar, H-beams and angles for supports and brackets
Common mistakes
- Entering a designation (NPS 4, DN 100) as a 100 mm outside diameter: NPS 4 actually measures 114.3 mm.
- Using outside or nominal diameter for velocity: velocity must use the area of the bore.
- Entering the sloping pipe length for a slope: slope percent is based on horizontal distance.
Related guides
- Pipe Weight Calculation: Formula and Example — Calculate pipe metal area, kg/m and total mass from OD, wall thickness, length and density, with a carbon-steel example and practical quantity checks.
- NPS, DN and OD: Nominal Size vs Actual Dimensions — Distinguish NPS and DN size labels from actual outside diameter, understand NPS 2 and DN 50 notation, and avoid inch-to-mm errors before calculation.
- Pipe Schedule and Wall Thickness Explained — Understand SCH 10, 20, 40 and 80 as wall designations, and compare how a thicker wall affects bore, kg/m and internal volume without assuming a pressure rating.
- Pipe Internal Volume: Calculate m³ and Litres — Calculate pipe bore area and fluid hold-up from OD, wall and length, with a worked example and practical filling, draining and flushing limitations.
- Pipe Flow Velocity: Flow Rate, Area and Example — Use v = Q/A with actual internal diameter, convert m³/h and L/min to SI flow, and understand why a smaller bore raises velocity at the same flow rate.
- Hydrotest Water Volume: Internal Volume and Water Weight — Calculate the water needed for hydrotests and flushing from pipe bores, and the weight of water-filled pipe for support checks, with a worked example.
- Steel Weight Calculation: Weight per Meter of Plate, Round Bar and H-Beams — Calculate cross-sectional area and unit weight of plate (kg/m²), round bar, H-beams and angles with formulas and worked examples, and see why results differ slightly from section tables.