Metric Bolt and Thread Chart
Look up pitch, tensile stress area, tap drill and spanner size of M3–M64 metric threads, and calculate proof load and an estimated tightening torque by property class.
Inputs
Updates as you type%
K
Results
Pitch
| Tensile stress area · As | 84.267 mm² |
|---|---|
| Pitch diameter · d2 | 10.863 mm |
| External minor diameter · d3 | 9.853 mm |
| Internal minor diameter · D1 | 10.106 mm |
| Tap drill · d − P | 10.25 mm |
| Spanner size · ISO | 18 mm |
| Spanner size · DIN | 19 mm |
| Proof load | 48.875 kN |
| Minimum tensile load | 67.413 kN |
| Preload | 36.656 kN |
| Estimated tightening torque | 87.974 N·m |
Metric coarse threads M3–M64
| Bolt size | Pitch · mm | Fine pitches · mm | Tensile stress area · As · mm² | Tap drill · d − P · mm | Spanner size · ISO · mm | Spanner size · DIN · mm |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 0.35 | 5 | 2.5 | 5.5 | 5.5 |
| M4 | 0.7 | 0.5 | 8.8 | 3.3 | 7 | 7 |
| M5 | 0.8 | 0.5 | 14.2 | 4.2 | 8 | 8 |
| M6 | 1 | 0.75 | 20.1 | 5 | 10 | 10 |
| M8 | 1.25 | 1, 0.75 | 36.6 | 6.75 | 13 | 13 |
| M10 | 1.5 | 1.25, 1 | 58 | 8.5 | 16 | 17 |
| M12 | 1.75 | 1.5, 1.25 | 84.3 | 10.25 | 18 | 19 |
| M14 | 2 | 1.5 | 115.4 | 12 | 21 | 22 |
| M16 | 2 | 1.5 | 156.7 | 14 | 24 | 24 |
| M18 | 2.5 | 2, 1.5 | 192.5 | 15.5 | 27 | 27 |
| M20 | 2.5 | 2, 1.5 | 244.8 | 17.5 | 30 | 30 |
| M22 | 2.5 | 2, 1.5 | 303.4 | 19.5 | 34 | 32 |
| M24 | 3 | 2 | 352.5 | 21 | 36 | 36 |
| M27 | 3 | 2 | 459.4 | 24 | 41 | 41 |
| M30 | 3.5 | 2 | 560.6 | 26.5 | 46 | 46 |
| M33 | 3.5 | 2 | 693.6 | 29.5 | 50 | 50 |
| M36 | 4 | 3 | 816.7 | 32 | 55 | 55 |
| M39 | 4 | 3 | 975.8 | 35 | 60 | 60 |
| M42 | 4.5 | 3 | 1,120.9 | 37.5 | 65 | 65 |
| M45 | 4.5 | 3 | 1,306 | 40.5 | 70 | 70 |
| M48 | 5 | 3 | 1,473.1 | 43 | 75 | 75 |
| M52 | 5 | 4 | 1,757.8 | 47 | 80 | 80 |
| M56 | 5.5 | 4 | 2,030 | 50.5 | 85 | 85 |
| M60 | 5.5 | 4 | 2,362 | 54.5 | 90 | 90 |
| M64 | 6 | 4 | 2,676 | 58 | 95 | 95 |
Overview
A chart for ISO metric threads from M3 to M64: coarse and fine pitches, tensile stress area, pitch and minor diameters, tap drill, and spanner sizes for hex bolts and nuts (ISO and DIN). Choose a property class (4.6 to 12.9) to calculate proof load and minimum tensile load to ISO 898-1, and an estimated tightening torque from a preload percentage and a nut factor. The table under the results compares pitch and spanner size for every size.
Formula
d2 = d − 0.649519P, d3 = d − 1.226869P, D1 = d − 1.082532P As = π/4 × ((d2 + d3) / 2)² (≈ π/4 × (d − 0.9382P)²) Tap drill ≈ d − P Proof load = As × Sp, minimum tensile load = As × Rm Preload F = proof load × preload percentage Tightening torque T ≈ K × F × d
Example
How to use
- Choose the nominal size (M3–M64) and the pitch. Coarse is the default; fine pitches can be chosen only where they exist for that size.
- Choose the property class. If you need a tightening torque, check the preload percentage (of proof load) and the nut factor K, and replace them with the specification's values where given.
- Read the pitch, stress area, tap drill, spanner sizes and proof and tensile loads. The torque is an estimate, so the bolting specification or the manufacturer's value takes precedence.
Engineering notes
- The tensile stress area is calculated with the ISO 898-1 formula. It agrees with published values (M12 84.3 mm², M20 245 mm² and so on) within 0.2%; the table values are rounded to three significant figures.
- Proof and minimum tensile loads use the ISO 898-1 stresses (class 8.8: Sp 580 and Rm 800 MPa up to d = 16 mm, 600 and 830 MPa above) times the stress area. Check nuts, washers and the clamped parts separately.
- Tightening torque T = K·F·d is an approximation. The nut factor K varies widely, roughly 0.1–0.3, with lubrication, plating and surface condition, so critical joints should follow the specification, the manufacturer's torque or a preload-control method.
- A tap drill of d − P is the usual rule; in practice the nearest standard drill is used, such as 10.2 mm for M12's 10.25 mm. Adjust for material and thread engagement.
- Spanner sizes differ between ISO 4032 and DIN 934 (and older JIS) for M10, M12, M14 and M22: ISO 16, 18, 21 and 34 mm against DIN 17, 19, 22 and 32 mm. Check the standard of the actual bolts and nuts.
- Clearance hole diameters are not included because the two published tables disagreed. Take them from the applicable standard, such as ISO 273.
Frequently asked questions FAQ
What does property class 8.8 mean?
The first number × 100 is the nominal tensile strength (800 MPa) and the second × 10 is the ratio of yield to tensile strength (80%), so class 8.8 has a nominal yield strength of about 640 MPa. This tool uses the ISO 898-1 minimum tensile strength and proof stress.
Why does M12 have both 18 mm and 19 mm spanner sizes?
ISO 4032 hex nuts are 18 mm; DIN 934 and older JIS nuts are 19 mm. M10 (16/17), M14 (21/22) and M22 (34/32) also differ by standard, so check the actual product's standard before choosing a tool.
Is a fine thread stronger than a coarse one?
At the same diameter the shallower thread gives a slightly larger stress area: M12 × 1.5 has about 88.1 mm², about 4.5% more than the coarse 84.3 mm². Fine threads are more easily damaged and take longer to assemble, though.
Can I use the estimated torque as it is?
Treat it as a reference. The same torque gives very different preloads depending on K, so critical joints such as flanges or structures should follow the specification's torque table, the manufacturer's values or a preload-control method such as tensioning.
Related tools
Work out the weight of plates and sections for supports and brackets with the steel weight calculator, and inch bolt dimensions with the mm-to-inch converter. Outside diameters and walls of the flanged pipe are in the pipe schedule chart.
Steel Weight Calculator
Calculate cross-sectional area, weight per meter and total weight of steel plate, flat, round, square and hexagonal bar, H-beams and angles from their dimensions.
Open calculatormm ↔ Inch Converter
Convert millimeters and inches in both directions, including a fraction rounded to the nearest 1/64 inch.
Open calculatorPipe Schedule Chart (NPS)
Pipe Schedule Chart
Look up outside diameter, wall thickness, bore and weight per meter of steel pipe by NPS and schedule (Sch 5S–160, STD, XS, XXS), and compare schedules.
Open calculator