ASME B16.5 Flange Chart
Look up outside diameter, thickness, raised face, bolt circle, bolt count and size and bolt holes of ASME B16.5 Class 150 and 300 flanges (NPS 1/2–24) in mm and inches.
Inputs
Updates as you typeResults
Flange outside diameter
| Flange outside diameter | 9 inch |
|---|---|
| Flange thickness · excluding RF | 22.225 mm |
| Flange thickness · excluding RF | 0.875 inch |
| Flange thickness · including RF | 23.813 mm |
| Raised face diameter | 157.163 mm |
| Bolt circle · PCD | 190.5 mm |
| Bolt circle · PCD | 7.5 inch |
| Number of bolts | 8 |
| Bolt size | 5/8″ |
| Bolt hole diameter | 19.05 mm |
| Bolt hole diameter | 0.75 inch |
ASME B16.5 Class 150 flange dimensions
| NPS | Flange outside diameter · mm | Flange thickness · excluding RF · mm | Raised face diameter · mm | Bolt circle · PCD · mm | Number of bolts | Bolt hole diameter · mm |
|---|---|---|---|---|---|---|
| 1/2″ | 88.9 | 9.5 | 34.9 | 60.3 | 4 × 1/2″ | 15.9 |
| 3/4″ | 98.4 | 11.1 | 42.9 | 69.9 | 4 × 1/2″ | 15.9 |
| 1″ | 108 | 12.7 | 50.8 | 79.4 | 4 × 1/2″ | 15.9 |
| 1 1/4″ | 117.5 | 14.3 | 63.5 | 88.9 | 4 × 1/2″ | 15.9 |
| 1 1/2″ | 127 | 15.9 | 73 | 98.4 | 4 × 1/2″ | 15.9 |
| 2″ | 152.4 | 17.5 | 92.1 | 120.7 | 4 × 5/8″ | 19.1 |
| 2 1/2″ | 177.8 | 20.6 | 104.8 | 139.7 | 4 × 5/8″ | 19.1 |
| 3″ | 190.5 | 22.2 | 127 | 152.4 | 4 × 5/8″ | 19.1 |
| 3 1/2″ | 215.9 | 22.2 | 139.7 | 177.8 | 8 × 5/8″ | 19.1 |
| 4″ | 228.6 | 22.2 | 157.2 | 190.5 | 8 × 5/8″ | 19.1 |
| 5″ | 254 | 22.2 | 185.7 | 215.9 | 8 × 3/4″ | 22.2 |
| 6″ | 279.4 | 23.8 | 215.9 | 241.3 | 8 × 3/4″ | 22.2 |
| 8″ | 342.9 | 27 | 269.9 | 298.5 | 8 × 3/4″ | 22.2 |
| 10″ | 406.4 | 28.6 | 323.9 | 362 | 12 × 7/8″ | 25.4 |
| 12″ | 482.6 | 30.2 | 381 | 431.8 | 12 × 7/8″ | 25.4 |
| 14″ | 533.4 | 33.3 | 412.8 | 476.3 | 12 × 1″ | 28.6 |
| 16″ | 596.9 | 34.9 | 469.9 | 539.8 | 16 × 1″ | 28.6 |
| 18″ | 635 | 38.1 | 533.4 | 577.9 | 16 × 1-1/8″ | 31.8 |
| 20″ | 698.5 | 41.3 | 584.2 | 635 | 20 × 1-1/8″ | 31.8 |
| 24″ | 812.8 | 46 | 692.2 | 749.3 | 20 × 1-1/4″ | 34.9 |
Overview
A chart of ASME B16.5 Class 150 and Class 300 flanges, NPS 1/2 to 24: outside diameter, thickness, raised face diameter, bolt circle (PCD), number and size of bolts and bolt hole diameter, in mm and inches. The table under the results compares every size of the same class, for checking piping drawings, preparing gaskets and bolts, or confirming a mating flange.
Formula
Dimensions are ASME B16.5 inch values; mm = inch × 25.4 Thickness including RF = thickness excluding RF + 1/16 in (1.6 mm) Bolt hole diameter = bolt diameter + 1/8 in Bolt spacing (arc) ≈ π × PCD / number of bolts
Example
How to use
- Choose the pressure class (150 or 300) and the NPS.
- Read the outside diameter, thickness, raised face diameter, bolt circle and the number, size and hole diameter of the bolts in mm and inches.
- Compare with other sizes of the same class in the table below, and check that the mating flange has the same class and NPS.
Engineering notes
- This chart covers ASME B16.5 Class 150 and 300, NPS 1/2–24 only. NPS 1/4 and 22 appear in only one published table and are left out; Class 600 and above are not included.
- Each value is used only where two published tables agree (outside diameter, bolt circle and holes: Engineering ToolBox and Texas Flange; thickness and raised face: Texas Flange and flanges.io). One table had wrong Class 300 outside diameters from NPS 4 up, and those values were not used.
- Thickness is shown both as the minimum excluding the 1/16 in (1.6 mm) raised face and including it. Sources often list only one of the two, so check which one you are comparing.
- Millimeter values are the inch values × 25.4. The ASME B16.5 metric tables round some values differently, so they can differ by roughly 0.1–1 mm.
- A class is a rating designation, not an allowable pressure. Allowable pressure depends on material group and temperature and comes from the B16.5 pressure–temperature rating tables.
- Bolt length, gasket dimensions and hub and bore dimensions are not included. Bolts are inch threads (UNC and so on) by default; when substituting metric bolts, check the hole clearance and the bolting load.
Frequently asked questions FAQ
Can a Class 150 flange be used up to 150 psi?
No. The class is a rating designation and the allowable pressure depends on material and temperature. For carbon steel (material group 1.1), Class 150 is about 19.6 bar (285 psi) and Class 300 about 51.1 bar at ambient temperature, falling as temperature rises. Check the B16.5 pressure–temperature rating tables.
Do JIS 10K or KS flanges mate with these?
Usually not. JIS and KS flanges of the same nominal size have different outside diameters, bolt circles, bolt counts and hole sizes from ASME. Check the mating flange's standard and class first.
How is bolt length determined?
Add two flange thicknesses, the gasket thickness, two nut heights and a thread allowance. It depends on the raised face and the gasket type, so check the bolt length tables in the B16.5 annex or the manufacturer's data.
Related tools
Compare outside diameter and bolt circle in the JIS flange chart to see whether a JIS flange mates. Check bolt pitch and stress area in the metric bolt and thread chart, and the outside diameter and wall of the flanged pipe in the pipe schedule chart.
JIS B 2220 Flange Chart
Look up outside diameter, thickness, bolt circle (PCD), bolt count and thread size and bolt hole diameter of JIS B 2220 5K, 10K, 16K and 20K steel pipe flanges by nominal size (A).
Open calculatorMetric Bolt and Thread Chart
Look up pitch, tensile stress area, tap drill and spanner size of M3–M64 metric threads, and calculate proof load and an estimated tightening torque by property class.
Open calculatorPipe Schedule Chart (NPS)
Pipe Schedule Chart
Look up outside diameter, wall thickness, bore and weight per meter of steel pipe by NPS and schedule (Sch 5S–160, STD, XS, XXS), and compare schedules.
Open calculator