Steel Weight Calculation: Weight per Meter of Plate, Round Bar and H-Beams
Every steel weight comes from area × length × density; only the way to get the cross-sectional area changes with the shape. Using plate, round bar, H-beams and angles common in pipe supports, brackets and stands, this guide calculates area and kg/m, explains why the results differ slightly from section-table unit weights, and shows quick mental estimates.
Published:
Concepts
Weight = area × length × density
For a member with a constant section along its length, the mass is the area A times the length L and density ρ. With carbon steel at 7,850 kg/m³, every 1 cm² of section weighs 0.785 kg/m. Once you have the area, any shape gives its weight per meter directly.
Plate and flat bar: kg/m² from thickness alone
A rectangular section W × t has a weight per area that depends only on thickness. Carbon steel weighs 7.85 kg/m² per millimeter, so a 10 mm plate is 78.5 kg/m² and a 12 mm plate 94.2 kg/m². One plate weighs its kg/m² times its area (width × length).
Round, square and hexagonal bar
The areas are πD²/4 for round bar, a² for square bar and (√3/2)S² for hexagonal bar measured across flats S. Carbon steel round bar can be estimated as kg/m ≈ 0.006165 × D² with D in mm, so a 50 mm bar is about 15.41 kg/m. For the same size, square bar is 4/π, about 27%, heavier than round bar.
Fillets in H-beams and angles
An H-beam's area is the web t1(H − 2t2) plus two flanges 2Bt2 plus the four web-to-flange fillets, (4 − π)r² ≈ 0.858r². An angle with sharp corners is t(A + B − t); rolled angles differ slightly because of the root and toe radii.
Basic formulas
m = A × L × ρ × n; kg/m = A [mm²] × ρ / 10⁶ Plate: A = W × t; kg/m² = t [mm] × ρ / 1,000 (= 7.85 × t for ρ = 7,850) Round bar: A = πD²/4 → kg/m ≈ 0.006165 × D [mm]² (ρ = 7,850) Square bar: A = a²; hexagonal bar: A = (√3/2) × S² H-beam: A = t1(H − 2t2) + 2Bt2 + (4 − π)r² Angle (sharp corners): A = t(A + B − t)
- W, t: plate width and thickness; D: round bar diameter; a: square bar side; S: hexagonal bar across flats. Section dimensions are usually given in mm.
- H: H-beam depth, B: flange width, t1: web thickness, t2: flange thickness, r: root radius. Angles have legs A and B and thickness t.
- A: area in mm² (÷ 100 = cm²), ρ: density in kg/m³ (carbon steel 7,850), L: length in m, n: quantity; kg/m = A [mm²] × ρ / 10⁶.
Worked example
Calculate, in carbon steel (7,850 kg/m³), a 1,500 mm × 10 mm plate 6 m long, a 6 m H 300×300×10×15 with r = 18 mm, a 50 mm round bar and an L 75×75×6 angle.
Plate 1,500 × 10 mm, 6 m: A = 15,000 mm²; 117.75 kg/m; 78.5 kg/m²; 706.5 kg H 300 × 300 × 10 × 15, r = 18 mm: A = 10 × 270 + 2 × 300 × 15 + 0.858 × 18² = 119.78 cm²; 94.03 kg/m; 6 m = 564.2 kg Without the fillets: A = 117.00 cm² (2.3% less) Round bar D = 50 mm: A = π × 50² / 4 = 1963.5 mm²; 15.41 kg/m (0.006165 × 50² = 15.41) Angle L 75 × 75 × 6 (sharp corners): A = 6 × (75 + 75 − 6) = 864 mm²; 6.78 kg/m
The plate weighs 78.5 kg/m²; times its 9 m² area that is 706.5 kg. The H-beam has 119.78 cm² and 94.03 kg/m, so a 6 m length is 564.2 kg; without the fillets the area drops to 117.00 cm², about 2.3% less.
With sharp corners the L 75×75×6 angle has 8.64 cm² and 6.78 kg/m, about 1% below the section table's 6.85 kg/m, because the area added by the root radius is left out.
How to use this in practice
Estimate material quantities and purchase weights for pipe supports, brackets and stands, or check member weights quickly before lifting and transport planning. Add bolts, welds, coating and a margin separately.
For plate quotes, thickness alone gives kg/m². Multiply by the plate area before nesting for the total, and add the cutting loss separately.
Common mistakes
- Section dimensions usually come in mm and lengths in m; mixing them gives errors of 1,000 times. Get kg/m first, then multiply by the length in m.
- H-beam designations read H × B × t1 × t2. H 300×150×6.5×9 is 300 deep with a 150 flange; swapping them changes the area.
- Using carbon steel density for stainless or aluminum members gives the wrong weight; aluminum is about a third of carbon steel.
Related calculators
Related guides
Frequently asked questions FAQ
Why does my result differ from the section table?
Section tables set unit weights from nominal areas that include corner radii and fillets. H-beams match almost exactly once the root radius r is entered, while sharp-cornered angles come out about 1% lower. Delivered material can also differ by the rolling tolerance.
Is there a quick way to estimate plate weight?
For carbon steel, thickness in mm × 7.85 gives kg/m²; multiply by the plate area in m². A 12 mm plate of 2.4 m × 6 m weighs 94.2 × 14.4 ≈ 1,356 kg.
How far is theoretical weight from actual weight?
It depends on rolling tolerance, galvanizing or paint, and cutting and fabrication. Use theoretical weight for quantity checks and comparisons, and the mill certificate or a measured weight where an exact value matters, such as settlement or lifting loads.
Engineering Disclaimer
Calculations and examples are references based on general formulas and stated assumptions. Before design, construction, manufacturing, inspection or approval, check applicable standards, project requirements and approved manufacturer or vessel data, and follow the required review procedures. These results do not imply certification or design approval by any authority.
Calculation disclaimer