Unit Converter
Convert length, pressure, mass, temperature, volume, flow and density.
mm ↔ Inch Converter
Convert millimeters and inches in both directions, including a fraction rounded to the nearest 1/64 inch.
Open calculatorPressure Converter
Convert one pressure value simultaneously to Pa, kPa, MPa, bar, kgf/cm² and psi.
Open calculatorWeight Converter
Convert mass between kilograms, metric tonnes, avoirdupois pounds and ounces.
Open calculatorTemperature Converter
Convert actual temperatures between Celsius, Fahrenheit and kelvin, with absolute-zero validation.
Open calculatorLength Converter
Compare SI length units with international inches, feet and yards using the meter as the base unit.
Open calculatorVolume Converter
Convert cubic meters, liters and US liquid gallons for tank capacities and pipe filling quantities.
Open calculatorFlow Rate Converter
Convert volumetric flow between hourly, minute and second units for pump and piping calculations.
Open calculatorGas Flow Standard–Actual Converter
Convert gas flow between standard conditions (Nm³/h, Sm³/h, scf) and actual operating pressure and temperature, with mass flow when the molar mass is given.
Open calculatorDensity Converter
Convert kg/m³ and g/cm³ when transferring material density data into engineering calculations.
Open calculatorWhat this section covers
Convert the length, pressure, mass, temperature, volume, flow and density units that mix in design documents and equipment specifications. One value is shown in every unit of its kind at once.
Conversion factors are defined values (1 inch = 25.4 mm, 1 lb = 0.45359237 kg, 1 kgf/cm² = 98,066.5 Pa and so on). A unit conversion does not change the basis (gauge or absolute pressure, standard-condition flow, temperature difference), so check the basis of the original value too.
Which tool should I use?
- mm ↔ Inch Converter — Convert drawing dimensions between mm and inch, with 1/64-inch fractions
- Pressure Converter — Reconcile Pa, kPa, MPa, bar, kgf/cm² and psi
- Weight Converter — Reconcile kg, ton, lb and oz
- Temperature Converter — Convert °C, °F and K (actual temperatures, not differences)
- Length Converter — Compare mm, m and km with inch, ft and yard at once
- Volume Converter — Reconcile m³, L and US gal
- Flow Rate Converter — Reconcile volumetric flows such as m³/h, L/min and L/s
- Gas Flow Standard–Actual Converter — Convert standard-condition flow such as Nm³/h or Sm³/h to and from actual operating flow
- Density Converter — Turn a material density in g/cm³ into kg/m³
Common mistakes
- Taking gauge pressure for absolute: changing the unit keeps the basis, so add atmospheric pressure separately.
- Putting a temperature difference into the temperature converter: a 20 °C difference is 36 °F, but an actual 20 °C is 68 °F.
- Mixing US and Imperial gallons: gal on this site is the US liquid gallon (3.785 L).
Related guides
- NPS, DN and OD: Nominal Size vs Actual Dimensions — Distinguish NPS and DN size labels from actual outside diameter, understand NPS 2 and DN 50 notation, and avoid inch-to-mm errors before calculation.
- Pipe Flow Velocity: Flow Rate, Area and Example — Use v = Q/A with actual internal diameter, convert m³/h and L/min to SI flow, and understand why a smaller bore raises velocity at the same flow rate.
- mm and Inch Conversion: Decimal and Fractional — Convert with exactly 25.4 mm per inch, understand decimal and fractional inches through 1/64, and check rounding error without confusing pipe nominal size with OD.
- Gauge and Absolute Pressure: Reading bar, psi and kgf/cm² — Understand barg versus bara and psig versus psia, how to add or remove atmospheric pressure, and how bar, psi, kgf/cm² and MPa convert, with worked examples.