Unit Conversion / ENGINEERING GUIDE

Gauge and Absolute Pressure: Reading bar, psi and kgf/cm²

A pressure value carries a basis as well as a unit. Gauge pressure, what most instruments show, takes atmospheric pressure as zero; absolute pressure takes a perfect vacuum as zero. The same 10 bar differs by about 1 bar depending on the basis, so when carrying values between specifications and calculations, check the basis as carefully as the unit. This guide shows how to change the basis and how the common pressure units convert, with examples.

Published:

Concepts

Gauge and absolute pressure

Gauge pressure (barg, psig) is measured from the surrounding atmosphere; absolute pressure (bara, psia) from a vacuum. The difference is the local atmospheric pressure; the standard atmosphere is 101.325 kPa = 1.01325 bar ≈ 14.696 psi. Most field gauges read gauge pressure.

Vacuum and negative gauge pressure

Pressures below atmospheric are negative in gauge terms: −0.8 barg is about 0.213 bara. Absolute pressure cannot go below zero, so gauge pressure bottoms out at about −1.013 bar on a standard atmosphere.

Unit conversion keeps the basis

Converting bar to psi changes only the unit: 10 barg is 145.04 psig, not psia. Add atmospheric pressure only when going from gauge to absolute, and subtract it only when going from absolute to gauge.

kgf/cm² is not the same as bar

1 kgf/cm² is a force unit defined with standard gravity (9.80665 m/s²): 98.0665 kPa, or 0.980665 bar. The kg/cm² on older Japanese and Korean equipment usually means kgf/cm²; treating it as bar is about 2% off.

Basic formulas

Pabs = Pgauge + Patm
Patm (standard) = 101.325 kPa = 1.01325 bar ≈ 14.696 psi
1 bar = 100 kPa = 0.1 MPa
1 kgf/cm² = 98.0665 kPa = 0.980665 bar
1 psi ≈ 6.894757 kPa
Vacuum: Pgauge < 0, Pabs ≥ 0
  • Pgauge: gauge pressure, Pabs: absolute pressure, Patm: atmospheric pressure. Bring them to one unit before adding or subtracting.
  • Standard atmosphere 101.325 kPa = 1.01325 bar ≈ 14.696 psi ≈ 1.0332 kgf/cm². Actual atmospheric pressure varies with altitude and weather.
  • 1 bar = 100 kPa = 0.1 MPa, 1 psi ≈ 6.894757 kPa, 1 kgf/cm² = 98.0665 kPa.

Worked example

Convert an equipment nameplate's 10 barg design pressure to absolute pressure and to psi, then treat a −0.8 barg vacuum and an older unit's 10 kgf/cm² (gauge) the same way, using the standard atmosphere.

Patm = 101.325 kPa = 1.01325 bar = 14.696 psi
10 barg + 1.013 = 11.013 bara
10 barg = 145.04 psig → 145.04 + 14.70 = 159.73 psia
10 kgf/cm²(g) = 9.807 barg → 10.820 bara
−0.8 barg → 0.213 bara

10 barg is 10 + 1.013 = 11.013 bara; in psi it is 145.04 psig = 145.04 + 14.70 = 159.73 psia. Changing the basis and changing the unit in separate steps avoids mistakes.

10 kgf/cm² (gauge) is 9.807 barg, about 2% below 10 barg, and 10.820 bara. The −0.8 barg vacuum is 0.213 bara.

How to use this in practice

Reconcile foreign vendor datasheets (psig, psia) with domestic specifications (barg, MPa), or feed gauge readings into formulas that need absolute pressure, such as pump and compressor calculations.

When carrying test pressures or relief valve set points, write g or a next to the unit and note the basis of the original document.

Common mistakes

  • Adding or removing atmospheric pressure when only the unit changes: bar to psi does not change the basis.
  • Using gauge pressure in gas-law or compression-ratio calculations, which need absolute pressure.
  • Treating kgf/cm² as bar: 1 kgf/cm² = 0.980665 bar, about 2% apart.

Related calculators

Related guides

Frequently asked questions FAQ

If the unit has no g or a, which is it?

It depends on the document. Field instruments and piping specifications are usually gauge, but process calculations and foreign data may be absolute. Without a marking, confirm the basis with the source document or its author.

What atmospheric pressure should I use at altitude?

Atmospheric pressure falls with altitude. Where exact absolute pressure matters, use the site's actual atmospheric pressure or the design basis value; for general conversions use the standard atmosphere, 101.325 kPa.

Is a pressure in MPa gauge pressure?

MPa is just a unit; the basis must still be stated. 1 MPa = 10 bar, so 1.0 MPa(g) is 10 barg, or about 1.101 MPa(a).

References

Engineering Disclaimer

Calculations and examples are references based on general formulas and stated assumptions. Before design, construction, manufacturing, inspection or approval, check applicable standards, project requirements and approved manufacturer or vessel data, and follow the required review procedures. These results do not imply certification or design approval by any authority.

Calculation disclaimer