MARINE / Horizontal Tank Volume Calculator

Horizontal Tank Volume Calculator

Calculate liquid volume and fill percentage of a horizontal cylindrical tank from the liquid height, with flat, hemispherical or 2:1 ellipsoidal heads.

Inputs

Updates as you type

Results

Liquid volume

5.867m³
Results
Liquid volume5,867.396 L
Liquid volume1,550.002 US gal
Total tank volume15.708 m³
Total tank volume15,707.963 L
Total tank volume4,149.605 US gal
Remaining volume9.841 m³
Remaining volume9,840.567 L
Remaining volume2,599.603 US gal
Fill percentage37.353 %
Liquid height / diameter40 %

Overview

Calculate the liquid volume, total capacity, remaining volume and fill percentage of a cylindrical tank lying on its side from the liquid height. In a horizontal cylinder volume is not proportional to height: a tank filled to 40% of its diameter holds only about 37% of its volume. The shell uses the circular-segment formula, and the two heads are added as flat, hemispherical or 2:1 ellipsoidal. Use it to turn a sounding of a fuel, ballast or storage tank into a volume.

Formula

R = D/2, h = liquid height (0 ≤ h ≤ D)
Segment area A(h) = R² · acos((R − h)/R) − (R − h) · √(2Rh − h²)
Shell liquid volume = A(h) × L
Liquid in both heads = k · πh²(3R − h)/3  (k = head depth/R: flat 0, 2:1 ellipsoidal 0.5, hemispherical 1)
Total volume = πR²L + k · 4πR³/3
Fill [%] = liquid volume / total volume × 100

Example

A flat-ended tank with a 2 m inside diameter and a 5 m shell filled to 0.8 m has a segment area of about 1.173 m², a liquid volume of about 5.867 m³ (5,867 L) and a total volume of about 15.708 m³, so it is about 37.35% full. The liquid stands at 40% of the diameter, but the volume is just over 37%. With 2:1 ellipsoidal heads on the same shell, the heads add about 2.094 m³: the total becomes about 17.802 m³ and the liquid about 6.605 m³ (about 37.10%). At exactly 1 m, half the diameter, the tank is 50% full whatever the heads.

How to use

  1. Enter the inside diameter and the shell length. The shell length is the straight part without the heads; check the unit of each field.
  2. Enter the liquid height measured from the bottom, between zero and the diameter, and choose flat, hemispherical or 2:1 ellipsoidal heads.
  3. Read the liquid, total and remaining volume and the fill percentage in m³, L and US gal. Note that the height ratio and the volume fill differ.

Engineering notes

  • Use inside dimensions. Outside diameter or plate thickness in the dimensions overstates the volume.
  • The tank is assumed to be level. Inclination, sounding-pipe position corrections and the volume taken by internals or heating coils are not included.
  • A 2:1 ellipsoidal head is calculated as an ellipsoid of revolution with a depth of a quarter of the diameter. Torispherical heads hold slightly different volumes; check the capacity table on the fabrication drawing.
  • Thermal expansion of the liquid and conversion to mass are not included. Multiply the volume by the density at the liquid temperature when you need mass.
  • Where a certified sounding table exists for the tank, it takes precedence. This calculation is for design review and approximate checks.

Frequently asked questions FAQ

How is this different from the vertical cylindrical tank calculator?

A vertical tank has a constant base area, so volume is proportional to liquid height. In a horizontal tank the liquid surface width changes with height, so a circular-segment formula is needed: near the bottom and top the volume changes little with height, and near the middle it changes most.

Why is the tank exactly 50% full at half the diameter?

The shell cross-section and the heads are symmetric about the horizontal centerline, so at h = D/2 the fill is 50% whatever the head type.

What if I do not know the head type?

Flat heads leave out the head volume and give the smallest result. Check the head type and depth on the fabrication drawing or nameplate. Pressure vessels commonly use 2:1 ellipsoidal or torispherical heads.

Related guides

KEEP WORKING

Use the vertical cylindrical tank calculator for an upright tank, or the rectangular tank calculator for a box-shaped tank. Convert the calculated volume to other units with the volume converter.