Horizontal Tank Volume: Why Liquid Height and Capacity Are Not Proportional
In a vertical tank, half the height means half the capacity; in a horizontal cylindrical tank it does not. The liquid surface changes width with height, so near the bottom the volume grows slowly as the level rises and near the middle it grows fast. This guide works through the circular-segment formula for the shell, adds flat, 2:1 ellipsoidal or hemispherical heads, and builds a table of fill against liquid height.
Published:
Concepts
A cross-section whose surface width changes
Cutting a horizontal cylinder across its axis gives a circle, and the liquid fills the lower circular segment, the area between the arc and a chord. The chord, the liquid surface width, is zero at the bottom and top and equals the diameter at the center. The same 10 cm of level therefore adds far more volume near the middle than near the bottom.
The circular-segment area
For a circle of radius R filled to height h from the bottom, the segment area is A(h) = R²·acos((R − h)/R) − (R − h)·√(2Rh − h²). The first term is the sector for the central angle and the second the triangle taken away from it. The shell's liquid volume is this area times the straight shell length L without the heads.
Head volume
The two heads together form an ellipsoid of revolution with radius R and depth a. Multiplying the spherical cap volume πh²(3R − h)/3 by a/R gives the liquid in both heads. Flat heads have a = 0, 2:1 ellipsoidal heads a = D/4 (= R/2) and hemispherical heads a = R. Torispherical heads differ slightly from this formula; check the manufacturer's capacity table.
Dip tables and real calibration
Calculating the volume at regular level steps gives a table that turns a sounding into a volume. Real tanks can differ from theory because of inclination, sounding-pipe position, internals and fabrication tolerances, so a certified calibration table takes precedence where one exists.
Basic formulas
R = D/2; 0 ≤ h ≤ D A(h) = R²·acos((R − h)/R) − (R − h)·√(2Rh − h²) Vshell = A(h) × L Vheads = k·πh²(3R − h)/3; k = a/R: flat 0, 2:1 ellipsoidal 0.5, hemispherical 1 Vtotal = πR²L + k·4πR³/3 Fill [%] = Vliquid / Vtotal × 100
- D: tank inside diameter, R = D/2: radius, L: straight shell length without heads, h: liquid height from the bottom. All in m, with 0 ≤ h ≤ D.
- A(h): circular-segment area occupied by liquid in m², a: head depth in m, k = a/R: flat 0, 2:1 ellipsoidal 0.5, hemispherical 1.
- Vliquid, Vtotal: liquid and total volume in m³ (× 1,000 = L); Fill: fill by volume in %, which differs from the height ratio h/D.
Worked example
Take a horizontal tank with a 2 m inside diameter and a 5 m shell, filled to 0.8 m. First calculate the shell alone with flat heads, then compare the same shell with 2:1 ellipsoidal heads, and finally build a fill table by changing the level.
D = 2 m; R = 1 m; L = 5 m; h = 0.8 m (h/D = 40%) A(h) = 1²·acos(0.2) − 0.2·√0.96 = 1.173 m² Flat heads: Vliquid = 1.173 × 5 = 5.867 m³ = 5867 L; Vtotal = π × 1² × 5 = 15.708 m³; Fill = 37.35% 2:1 ellipsoidal heads (a = 0.5 m): Vheads,total = 2.094 m³; Vtotal = 17.802 m³; Vliquid = 6.605 m³; Fill = 37.10% Dip table, flat heads (h/D → fill): 10% → 5.20%; 20% → 14.24%; 30% → 25.23%; 40% → 37.35%; 50% → 50.00%; 60% → 62.65%; 70% → 74.77%; 80% → 85.76%; 90% → 94.80%
With flat heads the liquid stands at 40% of the diameter but fills 37.35% of the volume. Adding 2:1 ellipsoidal heads adds 2.094 m³ for a 17.802 m³ total and 6.605 m³ of liquid (37.10%). Treating a tank with heads as flat-ended understates its total capacity by more than 10%.
In the dip table, 10% of the height holds 5.20% of the volume and 90% holds 94.80%: the gap between height ratio and volume ratio is largest near the bottom and top. At 50% the tank is symmetric, so it is exactly half full whatever the heads.
How to use this in practice
Turn soundings of fuel, lube oil, ballast or storage tanks into volumes, or compare capacities while changing tank dimensions during design. Record the inside diameter, straight length, head type and level datum with the result.
Level gauge marks and high-level alarm settings must be converted by volume, not height. In this flat-ended example, 90% by volume corresponds to about 84% of the height (1.69 m).
Common mistakes
- Using the vertical-cylinder formula πD²/4 × h treats 40% of the height as 40% of the volume, overstating this example by about 7%.
- Entering the overall length including heads as the shell length counts the head regions as cylinder and inflates capacity. Enter the straight length and the head type separately.
- Outside diameter or plate thickness in the dimensions inflates the volume: entering 2.02 m for a 2 m inside diameter adds about 2%.
Related calculators
Related guides
Frequently asked questions FAQ
At what liquid height is the tank half full?
Exactly at 50% of the diameter (h = D/2), because the circular section and the heads are symmetric about the horizontal centerline.
How do I calculate if I do not know the head type?
Check the head type and depth on the fabrication drawing or nameplate first. Flat heads give the smallest result and hemispherical heads the largest, so the real capacity usually lies between them.
What if the tank is inclined along its length?
The formula assumes a level axis. In an inclined tank the same sounding means different volumes depending on where the sounding pipe is, so a calibration table with trim correction or a separate calculation is needed.
References
Engineering Disclaimer
Calculations and examples are references based on general formulas and stated assumptions. Before design, construction, manufacturing, inspection or approval, check applicable standards, project requirements and approved manufacturer or vessel data, and follow the required review procedures. These results do not imply certification or design approval by any authority.
Calculation disclaimer